update

en/docs/dev_doc/hifi_audio/a316_1926v1/used.md

@@ -1,24 +1,24 @@
 ### PC扬声器声道设置说明
 前提，如果使用我们提供的 demo 板，和音频解码模组。如果您没有自己的驱动。需要先安装对应的驱动程序
-[下载地址](../../assets/download/A316/驱动1.zip)
+[下载地址](/assets/download/a316-8711-5.1make/a316demo驱动.zip)
 #### 1）当接好线之后，把其它 rx 端接入音响设备，把 tx 端的 demo 板接入电脑或手机
 
 正常来说通电时，tx端会和 rx 端自动配对
 
 是电脑的话，可能需要有所配置 打开运行（Win+R），输入【control】命令，按【确定或回车】，在控制面板中选择【声音】点击进入
 
-![控制板面.jpg](../../assets/images/speaker/控制板面.jpg)
+![控制板面.jpg](/assets/images/speaker/控制板面.jpg)
 
 #### 2）配置输出采样率与位深度
 在【声音】设置中 选择【播放】下的扬声器，鼠标右击，点击【属性】 再选择高级
-![位深度采样率.jpg](../../assets/images/speaker/位深度采样率.jpg)
+![位深度采样率.jpg](/assets/images/speaker/位深度采样率.jpg)
 
 #### 3）配置扬声器
 同样在鼠标右击扬声器，点击【配置扬声器】
-![配置扬声器.jpg](../../assets/images/speaker/配置扬声器.jpg)
+![配置扬声器.jpg](/assets/images/speaker/配置扬声器.jpg)
 
 #### 4）选择需要的声道, 请根据实际需要的音响环境选择
-![选声道.jpg](../../assets/images/speaker/选声道.jpg)
+![选声道.jpg](/assets/images/speaker/选声道.jpg)
 
 #### 5）所有线材电源连接成功后，可将RTL8711DCM PCB 上的复位键，全部按一次
-![pcb.jpg](../../assets/images/speaker/pcb.jpg)
+![pcb.jpg](/assets/images/speaker/pcb.jpg)

en/docs/dev_doc/hifi_audio/a316_1926v1/used_en.md

@@ -0,0 +1,25 @@
+### PC Speaker Channel Setup Instructions
+Prerequisite: If you are using our demo board and audio decoding module, and you don't have your own driver, you need to install the corresponding driver first.
+[Download Link](/assets/download/a316-8711-5.1make/a316demo驱动.zip)
+
+#### 1) After connecting the cables, connect other rx ends to audio equipment, and connect the tx end demo board to computer or phone
+
+Normally, when powered on, the tx end will automatically pair with the rx end
+
+For computers, some configuration may be needed. Open Run (Win+R), enter the [control] command, press [OK or Enter], select [Sound] in Control Panel and click to enter
+
+![Control Panel.jpg](/assets/images/speaker/控制板面.jpg)
+
+#### 2) Configure Output Sample Rate and Bit Depth
+In [Sound] settings, select the speaker under [Playback], right-click and click [Properties], then select Advanced
+![Bit Depth Sample Rate.jpg](/assets/images/speaker/位深度采样率.jpg)
+
+#### 3) Configure Speakers
+Similarly, right-click the speaker and click [Configure Speakers]
+![Configure Speakers.jpg](/assets/images/speaker/配置扬声器.jpg)
+
+#### 4) Select the required channels, please choose according to your actual audio environment needs
+![Select Channels.jpg](/assets/images/speaker/选声道.jpg)
+
+#### 5) After all cables and power connections are successful, press all reset buttons on the RTL8711DCM PCB once
+![pcb.jpg](/assets/images/speaker/pcb.jpg)